![]() ![]() MBSA uses different colored icons to represent vulnerabilities (“scores”) found on the scanned machine. Links to missing updates or security patches are displayed allowing them to be downloaded from the Microsoft Web site. ![]() The DSA Inactive node is set to zero during the excitation period when wired to a waveform generator Enable node, the desired behavior is realized.įigure 16.23. If there are waveform generators connected to other parts of the model, the DSA Inactive node at the lower right of Figure 2-31 can be wired to disable those generators. The DSA will automatically disconnect the input node so that any signals connected to the input are disabled during DSA excitation this is the case with the waveform generator in Figure 2-30. For all models in this book, the amplitude is set appropriately and users normally need not be concerned about this.Īll commands except the DSA excitation must be shut off during the excitation period. When doing so, always monitor the power converter output to ensure the system remains out of saturation for the entire excitation period. Setting the amplitude of the excitation is sometimes a matter of experimentation. However, if the amplitude is set too low, the signal-to-noise ratio of the system will be insufficient and the Bode plot will be distorted at high frequencies. If a system is driven into saturation, the excitation amplitude can be reduced using the Excitation Amplitude node at the top left of the DSA (see Figure 2-31). First, the system must remain out of saturation-the power converter must not be driven beyond its maximum during the excitation. This is ideal for a modeling environment because it minimizes the time the DSA must excite the system. When the random signal is applied to the model, the richness of the signal allows it to excite all frequencies at once. After the excitation, the DSA executes a fast Fourier transform (FFT) to convert the recorded data to a frequency-domain plot. During the period of excitation, the DSA monitors all variables in the model. The random signal is rich- it contains all the frequencies of the Bode plot. The DSA works by generating a random command for a short period of time. George Ellis, in Observers in Control Systems, 2002 2.4.4.5 The DSA Excitation Signal A good example of this is a write to a variable that is never subsequently read. In some cases, a flaw found by the analyzer may not result in a fatal program fault, but could point to a questionable construct that should be fixed to improve code clarity. However, since a static analyzer is not able to understand complete program semantics, it is not possible to totally eliminate false positives. A modern static source code analyzer is much better at limiting false positives than traditional UNIX analyzers such as lint. If an analyzer generates too many false positives, it will become irrelevant because engineers will ignore the output. Of course, one of the major design goals of a static source code analyzer is to minimize the number of false positives so that developers can minimize time looking at them. A false positive is a potential flaw identified by the analyzer that could not actually occur during program execution. By teaching the analyzer about properties of subroutines, users can reduce the number of false positives. ![]() For example, if a custom memory allocation system is used, the analyzer can be taught to look for misuses of this system. The analyzer can also be taught about properties of user-defined subroutines. Erratum I to the 2022 Editions of the Special Cargo Publications (PDF) in English has been issued, effective 1 January 2022.David Kleidermacher, Mike Kleidermacher, in Embedded Systems Security, 2012 3.5.4.5.1 Limiting False Positives.IATA Special Cargo Publications 2022 Erratum Air transport logistics (service levels, temperature ranges, packaging technology, risk factors, critical control points, temperature mapping, healthcare labelling, quality management, environmental considerations).Traceability and tracking (general, RFID).Acceptance and control (processes, hazard analysis, cold chain management, handling information).Documentation and labelling (specific documents, handling codes, labelling, marketing, WHO vaccine references).Packaging (general information, types and categories of packaging).Pharmaceutical facts and product types (temperature levels, market trends, product categories, biomedical research).Carrier regulations (general information, requirements and carrier variations).Government regulations (compliance requirements, variations by country).Applicability (shipper and carrier responsibilities, special handling conditions and transport conditions, compliance).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |